Netgain Motors

Hyper 9 IS Motor Kit

Add Chillplate?: NO

Add Compact Display?: NO

Add Throttle?: NO

Product variants

In stock, ready to ship

$5,400.00

Shipping calculated at checkout.

Description

The HyPer 9 IS is a Brushless AC motor system that is the ideal power-train for any light to mid-weight EV Conversion delivering class-leading torque, efficiency, and reliability. The HyPer 9 IS includes the brushless HyPer 9 Motor, HyPer-Drive X1 Controller/inverter, LV wire harness, and GV200QA contactor. The HyPer 9 operates at a 100V nominal, using 750 Amps, weighs approximately 120lbs, and delivers an impressive 173ft-lbs of torque at 0 RPM. This is a 3 Phase AC, Synchronous Reluctance Internal Permanent Magnet Motor (SRIPM). It requires a matching Synchronous X1 Controller/Inverter for power.

Features:

Industry Leading 3 Phase SRIPM Motor and Controller/Inverter
DC supply voltage from 62V to 130V, and currents up to 750A Peak
Brushless Motor
Cageless Rotor - Higher efficiency, no heat from wasted energy
Synchronous Fields - Full toque is harnessed without Rotor Slip
Up to 95% Efficiency!
Up to 50% higher torque than similar-sized AC Induction motors running at the same power levels!
Astounding performance in field weakening area with +50% power up to 5 times the nominal speed
Ultra-compact controller
Field Oriented Control (FOC) algorithm optimized specifically for Synchronous Reluctance Internatl Permanent Magnet motors
Fully customizable controller I/O
Extensive program customization from PC with Smartview Software
Robust and Reliable

The Drive End (DE) shaft is 1.125" in diameter with a 1/4" keyway.

Voltage:	100V Nominal
Current:	750 Amp
Efficiency Peak:	95%
KW Peak:	100 @ 125V
KW Continuous:	35 @ 125V
RPM Peak:	8,000
RPM Continuous:	3,300
Torque:	173 lbs.-ft @ 0 RPM
Regen:	Yes, Tailorable
Motor Diameter:	8.66"
Motor Length:	13.976"
Motor Weight:	120 lbs.
Controller Weight:	9 lbs.
Shaft:	Single-Ended, Keyed
Mounting:	B-Face (WarP 9)
Insulation:	Class "H"
Software:	SmartView

Specifications

Specifications Sheet for the Hyper 9 IS
Controller Drawing
Motor Drawing
Power Graph

Chill Plate

Greatly increase the continuous duty cycle of your Hyper-Drive X1 Controller/Inverter. Made from 6061 solid aluminum, this 5/8" thick plate is fitted with 1/8" NPT inlet and outlet ports. This is an unfinished aluminum plate and can be buffed with an abrasive pad for a matte finish or polished for a chrome look.

5/8" thick 6061 solid aluminum
1/8" NPT inlet and outlet ports
Mounting holes match X1 & X144 base
Includes liquid gasket maker

The HyPer-Drive X1 Controller has an operating temperature range of -40°C to +95°C. When the controller's heatsink temperature reaches +80°C, Thermal Cutback Mode will activate linear de-rating of the controller's output power. This linear de-rating continues until shut down at +95°C. Without a chill plate, the current rating of a properly mounted HyPer-Drive X1 Controller is 750A for 2 minutes. A liquid cooling loop, fed through this chill plate, can yield approximately 2-3 times the stock duty cycle. A liquid cooling system is strongly recommended for any application requiring a continuous rating above 200 Amps.

Compact Display

The SME Compact Display is an optional add-on component for any Hyper-Drive X1 Controller/ Inverter. The immediate EV capabilities of this LCD Compact Display include:

Display vehicle speed in MPH or KM/H. This is a calculated value determined by tire diameter and up to two gear ratios.
Display active fault code of highest priority.
Indicate main battery pack state of charge.
Indicate power de-rating due to Motor or Inverter over-temperature.
Cycle between 3 operating profiles with push button (E/S/H) switch. (Must be assigned in Clone file)
"Diagnostic Mode" to view System values such as - HyPer Motor RPM, Temperature, Torque, Current, and more.

Used Throttle Pedal Assembly:

Recommended Throttle Control Unit for any Hyper-Drive Controller/ Inverter. 0-5 V Potentiometer Pedal Assembly

Important Shipping Notes:

Shipping is automatically calculated at checkout to ship to a commercial address. All items that are being shipped to a residential address will have to be picked up at the nearest FedEx LTL service center. If you would like to ship this item to a residential address additional fees will apply. Please feel free to contact us if you have any further queries.

Pickup available at EVolve Electrics Office

Usually ready in 24 hours

Pairs well with

Hyper 9 IS Motor Kit

NO / NO / NO

$5,400.00